[tab name='Product Description']

***Sound Not Included. Shown for display purposes only.***

Not for the faint-hearted, but oh, so much fun. This monopole electrode addresses one of the biggest problems when using e-stim sounds for urethral play. How do you keep it in place?

No one wants an electro sound to fall out or go deeper than you had planned, so here is a solution. As suggested by a very good friend of mine, this holder allows you to secure your sound in place, and the best bit is that it is also an electrode that opens up all sorts of possibilities in how you play.

Some stimmers have already nicknamed it the "Yellow Submarine" LOL.

The main parts of this electrode are made from ABS (think Lego plastic), it's hard-wearing, non-porous and doesn't need painting or any other finish. To produce these electrodes, I have had to invest in new equipment, and the post-print processing time to get a smooth non-porous finish takes me a long time, which is reflected in the price. If you prefer the best, then this is the version for you. They will be available in very limited quantities, so grab one while you can.

The lower ring has a length of high-quality 6mm CR running through it, and this CR is in direct contact with the 4mm CR holding the cap in place. This turns the whole thing into a cage-style monopole electrode with lots of surface area (always a good idea to prevent hot spots).

The 4mm CR is easy to adjust and allows accurate positioning of the cap over your urethra. Once tightened it is secured by two 4mm cord locks (not shown) to lock it in place.

The design of the lower ring allows you to use an elastic band if you want to apply more pressure, and this can help keep things snug if you are a grower and shrinker as you stim.

The sound is held securely in place using a nylon bolt that runs through a brass heat-set insert in the cap. I opted for nylon bolts to ensure the sound is never scratched or damaged when you lock it in place.

It will be dispatched with the conductive rubber tubing already fitted.

This electrode takes 2mm TENS style plugs.

It is available in three sizes of lower ring:

1. 26mm/1" Inside Diameter.
2. 32mm/1.25" Inside Diameter.
3. 38mm/1.5" Inside Diameter.

For information about how to accurately measure the diameter of your penis, check out my Cock Ring Measuring Guide.

It is also available in two sizes of cap:

1. Compatible with sounds up to 8mm/0.35" in diameter.
2. Compatible with sounds up to 12mm/0.47" in diameter.

This product is made to order, and each takes me three days to print, post-process and finish. So please allow for the extra time needed for me to dispatch this bespoke item to you (I sometimes have ones ready-made and on the shelf, and these will be dispatched straight away).

Instructions

Check Out The Instructions For This Electrode

Note: This product is supplied as is, and I am not liable for any problems that arise from its use. It is sold as a novelty item and carries no warranty. Your statutory rights remain. Images shown are renderings.

Material

This product is 3D printed in ABS, a very strong plastic that has excellent mechanical properties. Once printed I post-process the components using a procedure called vapour smoothing. This uses Acetone vapour to actually melt and smooth the surface of the prints turning them from rough prints into smooth shiny prints that are non-porous.

Porosity is one drawback of the 3D printing process as it leaves microscopic holes in the surface of prints that are perfect for bacteria to grow in and hard to clean. Vapour smoothing prints seals these microscopic holes and imperfections, leaving the products smooth and sealed.

This is important as it makes cleaning post-play so much easier.

Sharing

However, I do not recommend these products are shared between partners unless you are fluid bonded for obvious reasons.

Product Care

After play simply wash in warm soapy water, anti-bacterial soap is best. Once body fluids have been washed off allow the electrode to dry thoroughly before you store it away for later use.

A deep clean can be carried out using Isopropyl Alcohol, this will kill bacteria and remove body oils.

Never use silicone-based lubes with conductive rubber-based electrodes as the silicone will bond to the conductive rubber, effectively destroying it and insulating it.

Instructions for use can be found here - Sound Clamping Monopole Glans Electrode Instructions

Global Shipping (pretty much)

I ship my products pretty much anywhere around the globe. I also charge shipping at cost plus a little extra for the packaging materials I use. I keep my postal rates as competitive as I can and even offer FREE SHIPPING on orders that meet the minimum requirement for that to kick in.

Here are some starter prices as an indicator (accurate rates will be displayed in the shopping cart):

• UK - Prices start from just £3.50 (non-tracked service).
• Europe - Prices start from just £5.15 (non-tracked service).
• US & Canada - Prices start from just £5.95 (non-tracked service).
• Rest of the world - Prices start from just £8.55 (non-tracked service).

Tracked services are available but they cost more.

Discreet Packaging

I ship all orders out discreetly in plain packaging and use a franking machine for postage. Where I have to fill in a customs declaration label, I do this discreetly, so there is no mention of "Anal Gaping Plugs" or anything like that. Discretion is key to my service. Descriptions such as "Tubing", "Plastic Formers", and "Sculptures" are often used on forms.

Customs Fees, Duty or Import Taxes

UK orders do not incur any of the above, but your order "may" be subject to importation duties or fees if you are an international customer. The threshold for this varies from country to country, and you should look into the situation where you are. I do not collect VAT for EU orders. You may be charged taxes or duties when your package is delivered. Please check your country's customs policies before you order.

[endtab]